AR-15 Jig - 80% Receivers

AR-15 Jig - 80% Receivers

Double click on above image to view full picture

Zoom Out
Zoom In

More Views

AR-15 Jig - 80% Receivers
$109.00
Our complete jig for completing the machining of a Tactical Machining 80% AR-15 lower receiver



*NOTE** LOWER RECEIVER SOLD SEPARATELY



This jig is compatible with both our Gen 2 and our Gen 3 Receivers

Availability: In stock

$109.00
OR
Description

Details

Our new and improved 80% AR-15 Lower Receiver jig is the highest quality lower receiver jig on the market. Every piece is replaceable on the jig. There are three top plates that are interchangeable to allow you to mill the fire control group. The side plates are fit with a drill bushing to allow you to properly drill the trigger and hammer pin
*NOTE** LOWER RECEIVER SOLD SEPARATELY
This jig is compatible with both our Gen 2 and our Gen 3 Receivers
Additional Information

Additional Information

Manufacturer Tactical Machining
Color Unfinished
SKU 10264
Weight 3.0000
Free Shipping No
Reviews

Customer Reviews 5 item(s)

Not the best jig on the market
I bought this jig from my buddy who never used it. The fatal flaw with this jig is that there's nothing bridging the bottom and only 2 little cap screws hold everything in place. When you tighten the jig into the vise on the table of my milling machine, the sides deflect in from the squeeze. If you try to tighten the vise less to try to minimize the deflection, the entire jig and lower assembly will move around in the vise while you're trying to mill. I ruined my first lower last night because of the inability to clamp this thing solid to the table. Review by Dave / (Posted on 2/1/2019)
Nice jig, missing screws
I got the jig, about to use it, but there were no screws included. I should be able to scrounge some up. The jig looks pretty nice so far. Review by Chris / (Posted on 12/26/2017)
Check the specs first before you start.
I bought the jig and 5 lowers quite a while ago. When I finally got around to using it, I completed all 5 lowers only to find the jig to be out of specification specifically at the safety selector hole. Every safety selector turned out to be 7-8 degrees crooked. It made functional lowers but I was disappointed with the unprofessional look of the safety selector. It may have been an isolated incident, but if you buy this, check that everything is in spec first. Comparing it to other jigs, I can see the the error very clearly now. Review by Michael / (Posted on 2/18/2016)
This simply works and is easy, especially with a drillpress and router!
I bought this jig a while back. It has now done 8 lowers. I did 2 using this jig on a vertical mill which wasn't terribly hard. I did a .308 from another manufacturer using the TM 308 sideplates (that I had to modify to fit) with these top plates using a drill press and router. 5 more were made by friends and relatives that I instructed and oversaw using the drill press and router method.

I found people that have experience using hand tools take between 2 to 2.5 hours machining using the drillpress and router method. All of them turned out very well. The drill/router method is a huge game-changer as you don't need to find someone with a mill that will let you use it, nor is the expense there. If you can run a drill press and a laminate router, you can do this.

The only problem I had was a couple of guys weren't holding the router tightly and when it jumped, they let go, and it buggered up the TM1002 profile plate. I will need to order a new one. Review by Jaydub / (Posted on 12/26/2015)
Easier than you think
I used TM's jig to complete 4 80% lowers. I used a drill press and an end mill to complete the process. Each one took aprox 60 min to complete from start to finish. With this jig you only have to worry about the depth of each cut. The rest was paint-by-colors easy. So easy I ordered 4 more of their gen 2's to complete next. Should take only half the time since the rear lug is already cut out. Prior to this, I have zero machining experience.

Thanks TM Review by LoMo / (Posted on 3/16/2015)

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.